Belt conveyor is easy to twist the parts of the inventory

2017-07-25

1, the workers step on the work of the belt head to sort out coal debris, accidentally foot in the coupling cylinder survey window, was twisted disability, the main reason for the incident: the co-cylinder investigation window without shield.

2, the workers in the belt machine patrol belt work conditions, because the coupling cylinder survey window short guard, accidentally hand into the window, resulting in their own disabled.

3, the belt driver illegal work to eliminate the work of the belt drum floating coal, with the belt and the hole caught towing, twisted its arm.

4, the belt working time The belt driver found the tail wheel drums have debris, which does not stop the belt work will reach out to the drum out of finishing debris, will be involved in the drum to death. During which the tail wheel without protective barrier equipment is also an important reason for the incident.

5, personnel to open the belt machine tail cover disposal After the completion of the floating coal, neither cover the cover is also out of the tail that is driving the test machine so that the belt is not accidentally driven into the tail wheel to death.

6, belt driver mind heavy, energy will not set, in the boot belt check belt roller work is not the normal process of accidentally falling into the drum to death. During which the ideological education of workers is not in place, resulting in workers awareness of indifference, the bad mood of the day to work can not self-regulation, work is the main reason for the loss of energy is the main reason.

7, the staff in the end of the joint work, the need to start the belt test machine, the belt driver adventure reckless, the operator has not yet evacuated the situation did not hit the signal will start the belt so that the work was accidentally involved in the drum to death. During which the belt driver illegal operation, risk reckless is the main reason for the incident. Work is not the development of security measures and arrangements for learning to strictly enforce the incident is also an important reason for the incident.

8, the staff found the belt roller skid, find the straw to fill in the drum and the belt between the handling of slippery problems, in the process of packing accidentally involved in the drum to death. During which the disposal of the belt when dealing with non-stop disposal is the main reason for the incident.

9, the staff in the belt machine belt, because the belt can not catch, so start the belt machine to pull, causing the staff was involved in the drum to death. During the start of the belt, the staff did not evacuate the belt near the drum is the main reason for the incident.
10, maintenance workers in the belt under the working time to the belt machine pit check the belt conveyor, accidentally rolled into the bottom belt, kneading to death. During which the staff of the safety awareness of indifference, adventure blind dry, non-stop situation into the belt machine tail pit is the main reason for the incident.

11, the staff in the belt machine belt, due to the conveyor belt is not short nail need to reverse the belt, so the squad leader to drive, 2 people with pliers grabbed the belt, one standing on the belt head to hold the stapler, In the squad leader move the belt after the head shaking the top of the standing staff imbalance, the left leg squeezed into the drum injury to death.

12, because the belt conveyor motor operating voltage is lower than the planning voltage, the motor does not move to show a slip appearance, anti-skid maintenance action power outages, personnel and then launch the belt and then operate the boost button to make the belt work, Ferocious, maintenance action after the power of the belt suddenly pulled down the stock drive wheel reversing the motor rotor, line bag thrown out to form a serious equipment damage somethin.
13, the belt driver found the belt roller showing a slip appearance, so the driver did not stop with the foot to step on the belt attempt to be resolved, accidentally wound into the drum injury to death.

14, the belt above the lamp is damaged, the staff sent to stop the station to replace the bulb on the belt, the belt suddenly launched to light it, struggling to stand up after the jump belt, the head touched the top of the beam fainted on the belt was pulled Into the coal bunker to death. During which the staff, although the RBI downtime, but did not contact the driver to tell that; the belt driver in the staff after the downtime did not identify the reasons for the start again to start the belt is the main reason for the incident.

15, belt driver violation in the belt work into the belt machine tail pit check the cause of the belt was rolled into the belt tail dead. During which the relevant departments of the operator is job training is not in place, the belt driver safety awareness indifferent, adventure reckless is the main reason for the incident.

16, the driver in violation of operating procedures, in the conveyor work in the conveyor belt roller pulverized coal, and not according to the rules of the use of special tools accidentally fall into the drum wound injury.

17, in the change when the conveyor clip, standing in the mechanical parts and the driver before driving, did not carefully investigate and prompt the staff to stand still accidentally fall into the drum wound injury.

18, in the equipment belt head undercover, the staff of the use of inverted chain lifting the lifting gear nose lifting process in the lifting of the nose suddenly cracked, resulting in lifting the belt head suddenly fell, the staff will be injured and killed. During which the lifting process only to lift the reducer lifting nose to lift, forming beyond the lifting nose bearing the ultimate attack cracking is the main reason for the incident.

19, inspectors found that the belt under the mouth blocked, went to stop the belt after work back to the next level of disposal. In the course of its disposal, the belt suddenly launched into the drum to death. During which the inspectors stopped the belt is not locked to start the switch, the belt driver off the private line, in the back of the post did not check the reasons for the shutdown, nor the investigation will launch the belt is the main reason for the incident.

20, in the removal of the belt during the work of the need to carry out the work of drag and drop, personnel illegal selection of belt roller instead of a small winch will be wrapped around the drum rope on the drum when the rope was dragged when the rope was rounded, in the inverted belt attempt to put the rope when the drum The staff into the drum wound injury to death. During which the relevant technical departments in the open work before the development of security technical measures to make the staff to learn, follow the implementation of the incident is also an important reason.

Tel:+86 532 67731351